Skip to content Skip to footer

ASP-ABF100J

Categoria: Product ID: 21706

Descrição

Model ABF100J ABF100B
Apply For Juki LK-1903A/LK-1903B/ LK-1903AN Brother 438FX
Rising Amount of Clamp Maximum:13mm
Feeding Time 0.35~0.5 Sec.
Button Type: Circle Flat Button
Size: Φ8~26mm ※Ø10mm is special specification, need to replace standard parts.
Button Hole Standard: 2&4 Holes Option: 3 Holes
Thickness of Button 1.5~3.5mm
Air Consumption 20 L/min
Air Pressure 0.5 MPa
Power Supply single-phase AC 200~240V 50/60Hz
Dimensions 440(W)x560(D)x280(H)mm

 

Remark:

Standard: Professional table, All Set of Button Presser Foot ,Small/Big Button Serrarted Plate and Bottom Plate, 12 Sets of Standard Button Carrier.
Option: 3-Holed of Button Carrier,Button Spacer,Button Spacer with Laser Light.

 *The definition of Button Size:
Extra small button size is Φ8~10mm, small button size is Φ10~20mm, and large button size is Φ20 ~ 26 mm. Basically, Button clamp of machine head is applied for Φ8~26mm, but that sewing extra/ large button size are depend on its thickness and convexity.

 

SUGGESTION OF SELECTING THE SERRATED PLATE
Button
Size: Φ8~16mm
Size: Φ16~25mm
The small serrated plate
The Big serrated plate

 

 

Button sewing machine with auto button feeder enhances 300% efficiency of button sewing.

Cycle Time: 2.2 Sec./Button; 13,090 Buttons/8 Hr

 

 

 

BUTTON CARRIER MODULE

Modularized button carrier is for different button size and replacement.

PANEL

User friendly interface, all sewing  parameters are clearly shown.

 

SENSOR SIGNAL DETECT

Checking the sensors detecting by A02 function of operation panel.

FLIP MECHANISM

Flip mechanism enhance the accuracy of ø16mm up button by auto air-blow.

SMART SENSOR OF BUTTON CLAMP

Button clamp can detect the button position and avoid sewing without button.


BUTTON CHANNEL ADJUSTMENT

Channel adjustment is controlled by stepping motor accurately .

DISCHARGING

Press the key and then remove all the buttons in the channel.

ELECTRONIC AUTOMATIC MEASUREMENT OF BUTTON SIZE

Accurate, Ultrafast, adjusting different button in a short time.

BUTTON CLAMP OF MACHINE HEAD

Button clamp is suitable for variety button size, the clamp can be used in different button size and no further adjustment needed.

 

 

SPECIFICATION OF BUTTON

Codes of Parts X+0.05
-0.05
D+0.05
-0.05
Button
Holes
ABF118 2.2 1.0 4
ABF119 2.2 1.0 2
ABF120 2.4 1.2 4
ABF121 2.4 1.2 2
ABF122 2.8 1.2 4
ABF123 2.8 1.2 2
ABF124 3.2 1.2 4
ABF125 3.2 1.2 2
ABF126 3.6 1.2 4
ABF127 3.6 1.2 2
ABF269 2.6 1.2 4
ABF270 2.6 1.2 2
ASO-ABF100J.100B-07

BUTTON SHAPE

Available Shape of Button
Two sides must be have obvious differences to make sure that the machine can differentiate the front & reverse side of the buttons.The convex / concave must above 1.2mm height difference.
Unavailable Shape of Button
The machine can’t identify the button when both sides are similar without obvious
differences.